Chaps Do Not Stop the Chain
Chainsaw chaps and protective pants do not stop the chain. British Columbia's own faller training standard says so directly: approved leg protection does not prevent penetration of the chain, but it can lessen the severity of a cut.
That is a meaningful difference from how most people understand the product, and it changes what you expect from it. The pads buy you a shallower wound and a chance, not immunity.
How the protection actually works
The BC Faller Training Standard describes protective pants as mandatory for fallers, preventing abrasions and bruising and lessening the severity of a cut, while protecting the legs during kickback.
The mechanism is mechanical rather than armoured. The pads contain ballistic nylon or Kevlar fibres that the chain catches and drags out, and the loose fibre bundles jam the drive sprocket and stall the saw. The protection comes from stopping the chain, not from resisting it.
Which is why damaged protection fails completely. Protective pants or chaps should not be worn if torn or damaged, and should be replaced or repaired according to the manufacturer's instructions rather than patched.
There is a rating to check when buying. Protection must meet the threshold chain speed specified in the applicable standard, with a minimum of 3,600 feet per minute, and 4,100 feet per minute recommended as best practice. Some oil and gas operations require the higher figure outright.
Protective pants or full-length chaps must meet the requirements of the current WorkSafeBC standard and be properly labelled, which is the same claim-versus-marking point that applies to every other category of protective equipment.
And the whole system assumes the saw is being used properly. Leg protection is the last thing in the chain of controls, not the first.
Storm cleanup is treated differently
This distinction matters right now, with windstorm season underway.
BC Hydro's standard requires any worker falling a standing tree larger than six inches in diameter to be certified to the BC Faller Training Standard, or to be a Certified Utility Arborist with falling certification acceptable to WorkSafeBC.
It then adds a note that is easy to miss: this requirement does not apply to work related to clearing trees that have already fallen, such as storm damage.
So the certification threshold attaches to felling a standing tree, not to bucking one that is already down. That is a real and sensible line, and it is not permission to treat storm cleanup as low risk.
A fallen tree is loaded in ways nobody designed. Trunks under bending tension, limbs compressed against the ground, root plates waiting to stand back up, and the whole thing resting on something that may shift when a cut releases it.
Delimbing has its own rules for that reason. The tree must be resting solidly on the ground, and nobody should walk on the trunk while it is being delimbed.
Storm work also arrives alongside the hazard covered in our guide to overhead power line limits of approach, since a tree that came down in a storm is frequently in contact with a conductor, and so is the ground around it.
Do not drop start
CCOHS lists a handful of saw-handling prohibitions that cover most of the self-inflicted injuries.
Do not drop start, meaning starting the saw while holding it in your hands rather than braced. That method leaves one hand controlling a running saw and produces leg cuts.
Do not start a saw within three metres of fuel containers, do not carry a saw while it is running, and do not leave one running unattended.
Do not stand directly behind the saw. The kickback arc comes back along the plane of the bar.
And do not use a saw with damaged, improperly adjusted, loose or missing parts, which in practice means the chain brake, the chain catcher and the throttle interlock get checked rather than assumed.
Full-wrap handlebars are required under the BC faller standard because they give control of the saw in every cutting position and let the saw be used with a pulling chain, which is the orientation that avoids kickback.
Kitting out a storm or grounds crew?
Workman Industrial stocks hard hats, hearing and eye protection, gloves and CSA-certified safety footwear, shipped across Canada.
Two standards, and the edition differs by province
The Canadian standards are CSA Z62.1, Chainsaws, and CSA Z62.3, Chainsaw Kickback. Which edition applies depends entirely on where you are.
Provincial regulations adopt them by reference at different vintages. Some jurisdictions still reference the 1995 edition of Z62.1, others the 2003, 2011 or 2015 editions, and several allow a standard offering equivalent or better protection.
That matters when buying equipment or writing a procedure, because citing the wrong edition in a safe work procedure is the kind of thing an inspector notices.
What the standards require in practice is consistent: a chain brake, a safety chain, a chain catcher, and features that minimize kickback, along with vibration isolation in some jurisdictions.
New Brunswick adds two requirements worth borrowing regardless of where you work. Operators are not to work alone, and they are to carry or keep close the pressure bandage provided by the employer.
That bandage is the honest companion to the chaps point at the top of this article. It exists because the protection reduces severity rather than eliminating the wound.
The rest of the kit
Chainsaw work requires a full set rather than a saw and a pair of chaps.
Head protection, with the particular note that overhead hazards in tree work are the reason rather than a formality. Our hard hat safety guide covers selection, and combination units with integrated face screen and ear defenders are the practical answer for saw work.
Hearing protection is not optional at chainsaw noise levels, covered in our hearing protection guide, and eye protection is required alongside a mesh screen rather than instead of it, covered in our safety glasses guide.
Gloves protect against abrasions, cuts and cold, and they also provide grip on the saw, which matters while filing and handling the chain as much as while cutting. Our guide to work gloves covers general selection.
Footwear is where the Canadian marking system has something specific to say. Our guide to CSA work boot symbols covers the white rectangle with the green fir tree, which marks footwear with chainsaw protection, alongside the toe and sole marks.
High-visibility apparel is mandatory for fallers whose location has to be checked regularly and when working close to moving equipment, covered in our guide to CSA Z96 classes and levels.
We do not stock chainsaw protective pants, chaps or chainsaw-rated footwear. Those come from forestry and arborist suppliers, and they are the two items this article is most insistent about.
A dull chain is a safety problem
Maintenance gets treated as a performance question and it is a control.
A dull chain does not cut, so the operator pushes harder, and a saw being forced is a saw that grabs, kicks and skates off the cut. Sharp chains cut on their own weight.
Chain tension is the same. A loose chain can come off the bar entirely, and a chain that leaves the bar at full speed is the scenario leg protection exists for.
Safety features need checking rather than assuming. The chain brake should engage, the chain catcher should be present and intact, and the throttle interlock should prevent the saw running without a deliberate grip.
New Brunswick's guidance on tree removal requires employees doing the work to be competent and properly equipped, with specific requirements for foot and leg, eye, head and hearing protection, which assumes a saw maintained to match.
Filing happens with the saw off and the chain brake on, and gloves on, because a sharp chain is sharp whether or not the engine is running.
Fuelling is its own moment: engine off, cool, away from ignition sources, and not where the saw will then be started.
Distance, and what happens after the cut
Where people stand decides most of the outcomes in tree work.
The two tree-lengths rule sets the minimum separation between workers during falling, because a tree can go somewhere other than planned and the next tree can come with it.
The escape route is planned before the cut, not chosen during it. New Brunswick's guidance is to move at least three metres from the tree at a 45 degree angle from the direction opposite the intended fall.
Working above ground brings fall protection into it. Above three metres, tree work requires a fall arresting system or an appropriate saddle and life line designed for tree maintenance.
Weather is a control rather than a backdrop. Wind changes where a tree goes, rain and frost change footing, and cold reduces grip and judgement on a tool that needs both. Our guides to slip resistance at work and cold stress at work in Canada cover both.
First aid provision has to match the distance from help, which for most tree work means more than a basic kit and a phone. Our guide to CSA Z1220 first aid kit requirements covers the classification system.
For the wider programme see the complete PPE checklist for Canadian workers, our guide to PPE requirements for Canadian construction sites, our guide to who pays for PPE in Canada and our guide to CSA certified versus CSA compliant.
Frequently Asked Questions
Do chainsaw chaps stop the chain?
No. The BC Faller Training Standard states that approved leg protection does not prevent penetration of the chain, but can lessen the severity of a cut and protect the legs during kickback. The pads work by pulling out and jamming the drive sprocket to stall the saw, rather than by resisting the chain.
What rating should leg protection have?
It must meet the threshold chain speed specified in the applicable standard, with a minimum of 3,600 feet per minute. A rating of 4,100 feet per minute is recommended as best practice, and some oil and gas operations require it. The protection must also be properly labelled.
Can torn chaps still be used?
No. Protective pants and chaps should not be worn if torn or damaged, and should be replaced or repaired according to the manufacturer's instructions. The protection depends on the fibre pads being intact, since damaged pads cannot pull out and jam the sprocket.
Do I need faller certification for storm cleanup?
Certification requirements generally attach to falling standing trees rather than clearing ones already down. BC Hydro's standard requires certification for falling a standing tree larger than six inches in diameter, and explicitly notes it does not apply to clearing trees that have already fallen. Confirm the requirement that applies to your work.
What is drop starting and why is it prohibited?
Drop starting means starting the saw while holding it in your hands rather than braced on the ground or against your body. It leaves only one hand controlling a running saw, and it is a known cause of leg cuts. Also keep saws at least three metres from fuel containers when starting.
Which Canadian standards apply to chainsaws?
CSA Z62.1, Chainsaws, and CSA Z62.3, Chainsaw Kickback. Provincial regulations adopt them by reference at different editions, ranging from the 1995 version through to 2015 depending on jurisdiction, with several allowing a standard offering equivalent or better protection. Check which edition your regulation cites.
Head, hearing, eye and foot protection for the crew
Browse hard hats, hearing protection and CSA-certified work boots at Workman Industrial, with Canada-wide shipping.
This guide is general workplace safety information and is not chainsaw or faller training. Chainsaw and tree work requirements, certification thresholds, adopted standard editions and leg protection specifications are set by provincial regulation and differ between jurisdictions. Falling standing trees requires certification in many circumstances. Confirm your requirements with the occupational health and safety authority that governs your workplace, and never work on or near a tree in contact with a power line.